Icon Case with Heatsinks & Fan Stressberry Test

Disclaimer:

This guide is provided for information and as it is. Cytron Technologies will not be responsible for any damage or data lost during the installation process. Do backup your microSD card if you have any concern.

Hardware:

logo

 

 

First of all, why subject your Raspberry Pi to this level of stress? In the case of Raspberry Pi 4, the A72 CPU is so powerful that it can overheat if it doesn’t have enough cooling. This results with the CPU being governed (slowed down) to reduce the electrical energy being consumed, and in turn, reducing heat generation. The RPi 3B+ and predecessors could also overheat, however, it was less of a problem for the majority of use cases. A quick stress test, in this case, will reveal if your Raspberry Pi 4 can run at full CPU-load in its case/environment without overheating and not slowing down.

The goal of this tutorial is to create a chart which depicts:

  • A stabilization period at the beginning
  • A period of time for full-load CPU
  • View the CPU temperature
  • View the CPU speed (to witness if the CPU is being governed, or not)

There are a million ways to cool down your Raspberry Pi: Small heat sinks, specific cases, and some extreme DIY solutions. Stressberry is a package for testing the core temperature under different loads, and it produces nice plots which can easily be compared.

The run lets the CPU idle for a bit, then stresses it with maximum load for 30 minutes, and lets it cool down afterwards. The entire process takes around 45 minutes. The resulting data is displayed to a screen or, if specified, written to a PNG file.

 

 

Step 1: Enclosure installation steps

 

Paste four pieces of heat sinks and install the Raspberry Pi board to the case.

photo 2021 10 05 16 43 01

Insert the side plate.

photo 2021 10 05 16 42 06

If you need to connect WLAN cable or USB, please remove the side plate, as the picture shows.

photo 2021 10 05 16 43 08

Install the fan to the top cover using four screws.

photo 2021 10 05 16 43 11

Connect the fan to Raspberry Pi as the picture shows.

photo 2021 10 05 16 42 49

Fix the top cover to the case.

photo 2021 10 05 16 42 54

Mount the screws of the case.

photo 2021 10 05 16 43 14

Paste the stickers to the both sides of the case.

photo 2021 10 05 16 42 39

Install the base. There are two options to install the base.

photo 2021 10 05 16 42 44
Option 1
photo 2021 10 05 16 42 58
Option 2

The Raspberry Pi is now can be power ON.

photo 2021 10 05 16 43 05

 

 

Step 2: Result for the stress test

I have overclocked and ran the stress test on the Icon Case with Heatsinks & Fan to observe how great the enclosure dissipates heat from the Raspberry Pi 4. The chart below shows the stressberry graph for the Icon Case with Heatsinks & Fan.

b

From the chart, we can see that the Raspberry Pi can dissipate heat better with the case. From my observations:

Icon Case with Heatsinks & Fan – this type of enclosure applies an active cooling mechanism. From the chart, it is obvious that this enclosure is really good at dissipating heat and keeping the raspberry pi temperature below 60 degrees Celsius with a fan ON. Despite that, it can be a problem when the fan is OFF since this Icon case does not have an adequate air flow which causes the temperature to be extremely high.

Overclock test – the Raspberry pi is overclocked to observe how far the clock frequency can be increased while maintaining the CPU temperature below 80 degree Celsius. The Raspberry Pi can be overclocked to maximum 2.1 GHz with this case.

 

Now you can see that enclosure for Raspberry Pi 4 is really important in dissipating the CPU heat. Interested in having this type of enclosure for your Raspberry Pi? 

Let’s get the enclosure at our Cytron product webpage 😁. 

 

Kindly refer this tutorial for the Stressberry test.

Stressberry Test on Raspberry Pi 4

 

 

Leave a Comment

Your email address will not be published.

Share this Tutorial

Share on facebook
Share on whatsapp
Share on email
Share on print
Share on twitter
Share on pinterest
Share on facebook
Share on whatsapp
Share on email
Share on print
Share on twitter
Share on pinterest

Latest Tutorial

Icon Case with Heatsinks & Fan Stressberry Test
Low Profile Aluminum Case Stressberry Test
Stressberry Test on Raspberry Pi 4
K-Type Thermocouple With Maker UnoX And Blynk
Real-Time IoT Room Monitoring on Maker Pi Pico Using pyRTOS
Tutorials of Cytron Technologies Scroll to Top